Hi,
I have tried to read out the Landys-Gyr E650, finding out it's a DLMS meter

I'm using the following hardware:

- Raspberry Pi 3B
- A RS485 cable connected to the meter, installed by the network operator.
- the RS485 cable connected through ch341-uart converter through usb on the raspberry Pi

Having cloned https://github.com/gurux/gurux.dlms.python and installed all the dependencies, I have tried to get it working through, but so far I get the following outputs:

Hi Mikko,

Initially, I have connect meter using high-level security. Then set the secret from Association 0.0.40.0.5.255. Now I am trying to connect a meter with updated secret but not able to connect.

Can you please check the following logs and provide an update.

Let me know if you require more information about the same.

Hi, I am trying to read the time periods of the Itron SL7000 meter. In doing so, it indicates that there is an error and the reading cannot be done per period. Is there an example where you indicate how it is done and how the dates are set for reading? I am using the gxDemandRegister registry. The meter answers the following:

Hi,
I'm trying to connect to Kamstrup (686-162-WK-65) meters using bluetooth optical probes from a Xamarin Android app. These meters only support IEC (61036).
I'm able to connect to the bluetooth optical probe however, I'm not sure how to integrate with the Gurux.Serial API.
Any help, guidance would be appreciated.

Thanks, Vincent

Hi Mikko,

I trying to connect meter (IS15959) with the authentication level as high.
Using GXDLMSDirector I can connect meter properly. But when I am trying from our test application it is not able to connect and gives the following response :

7EA00F61037410D7E6E700D8010683377E

Can you please check and revert back asap.

I have set all required parameters to connect the meter with authentication high.
Do I need to set any other configuration?

Hi Mikko,

I am trying to read Image transfer DLMS object from Indian standard meter (IS15959-2) using the GXDLMSDirector application.

Meter is connected with High-level security.

I can read all attributes from meter but In that why Activate, Verify and Update buttons are disabled? Please find the attached screenshot for the same.

Is there any configuration from the GXDLMSDirector application?

Hello,

I want to read the Iskraemeco meter. I will use c # language and serial port for this.
I'll just read the clock and active energy value. OBIS Code(clock=0-0:1.0.0 and Active energy= 1-0:1.8.0)
The codes at https://github.com/Gurux/Gurux.Serial came very mixed.
Is it possible to add a simple code that will read the two parameters I wrote?

Thank you.

Meter Info
Name: MT383 DLMS
password: 12345678
physical address:17
logical adress:1
client adress:1

Hi Mikko,

I am trying to write data into meter having Indian standard manufacturer.

Following are the configuration :
Security: High
Authentication level : AuthenticationEncryption
Action : AuthenticatedReadWrite

I have written data into meter for 0.0.96.13.1.255 obis code for attribute index 2. After the power cycle, I am able to read the same data which was written.

Now I am removing device and added same device again into the GXDLMDIrector application and trying to read the same attribute but did not get written value.

Hi Mikko,

I have connected meter using the following configuration:

Authentication Level : Low
Security : AuthenticationEncryption
Manufacturer: Indian Standard

Using authentication level None, Meter is properly disconnect and connect multiple times. But using authentication level low meter is not able to disconnect properly.

Hi Mikko,

I am trying to do secured connection with the meter using the serial interface with following configuration.

Authentication : Low
password : ABCD111
Secured Connection Configuration : As shown in attached image.

It gives error message as
"Specified argument was out of valid values.
Parameter name: Invalid System Title".

Please let me know how I can do secured connection.

Thanks,
Bhaumik