Forum Rules

Before commenting read Forum rules

Don't comment the topic if you have a new question.

You can create a new topic selecting correct category from Gurux Forum and then create a new topic selecting "New Topic" from the top left.

Description

Questions and comments about DLMSDirector.

Image
By jan.kolar , 30 August, 2023

Failed to receive reply

Forums
DLMSDirector

Hello,

reading association view is terminated by error message:
Failed to receive reply from the device in given time.
As i remember from distant past this function never was reliable. The meter type is Landis&Gyr E550, client id = 80 (Level 4). When I analyze logs i see that reading is terminated on this packet (please see last three packets):

By OK1FMD , 14 August, 2023

SM402D reading through an optical interface

Forums
DLMSDirector

HI,
I have a smart electric meter SM402D. I read the electricity meter via an IP modem (Wrapper). But if I need to read the electricity meter via the optical interface (Mode E). I have a problem with identification at the beginning of communication. The electricity meter has the identification "MAC" see the attachment. I didn't find support for this meter in GXDLMSDirector. Can someone help me. Thank you very much.
Best Regards Martin

By tfo_develco , 10 August, 2023

Not able to get consumption data from Kamstrup Omnipower three-phase meter

Forums
DLMSDirector

Hi,
I'm trying to read consumer data from a Kamstrup Omnipower three-phase meter with no luck.
I'm using the HAN (CCC) port.
I can establish a connection with authentication: None and read data like S/N etc.

My goal is to be able to read the consumer/consumption data at least every second.
I have the GPK11, GPK61 and GPK62 keys for the meter. But right now I'm just trying to establish a secure connection with authentication: Low and it fails.

By mki123 , 10 August, 2023

Reading from Holley Meter

Forums
DLMSDirector

Hi,

I am new to DLMS and so would appreciate some guidance. I have a Holley meter that I am attempting to get information from over RS-485. Using the DLMSDirector, I can connect to the meter but am getting an error when I try to read the Assosciation View with a temporary failure.

Excerpt from the log is as follows:

By shabin shanavas , 31 July, 2023

Trying to connect DLMSDirector with L&T watthour meter.

Forums
DLMSDirector

Hi,

I am trying to communicate with the L&T AC static watthour meter ER300P through the Gurux GXDLMSDirector program. Meter is directly connected with RS232 to a TTL (serial). I am also attaching a screenshot of the settings. But I am getting a warning message of timeout as "Failed to receive reply from the device in given time". Is there any changes in the settings?

Well thank you.

By janciivt , 27 July, 2023

MCS301 -

Forums
DLMSDirector

Hi,
I am trying to communicate with the Metcom MCS301 electricity meter through the Gurux GXDLMSDirector program. I am also attaching a screenshot of the settings. Can you advise me how to find out the physical address of the electricity meter?
Well thank you.

By pooja_g , 25 July, 2023

Image transfer object read - Service not allowed Deciphering failed

Forums
DLMSDirector

Hi,
I have successfully established HLS authentication with meter and Gurux. I tried to read Image transfer object, and I am getting Exception response Service not allowed Exception.Deciphering failed.
Below is the log:
14:34:36 Read object type ImageTransfer index: 2
TX: 00 01 00 30 00 01 00 20 C8 1E 30 00 00 0F 9A 04 43 53 B4 AC 5F A5 FC D5 C9 7E C8 F3 12 95 91 3F AD AB 46 C1 BA 2E B4 49
14:34:40
RX: 00 01 00 01 00 30 00 1C CC 1A 30 00 00 07 22 B0 B1 52 D1 0F 66 DB 00 17 95 0C 5F D9 B9 24 27 DE 9F 77 A4 10

DLMSDirector