Hi!

I'm trying to read the CEWE Prometer 100 W with GXDLMSDirector and it always return this message "Failed to receive reply from the device in given time"
I use the Device monitoring studio to capture the READ/WRITE packets in reading time and realise that the source/destination in write packet is not simillar to the packet I captured when I successfully connected to the meter via M-Cubed 100 application.

Hi,

I'm trying to read the EMH LZQJ-XC meter using DLMSDirector.
As far as i know i should to use this formula: SN%10000+256.

The question is where should I provide this formula (which tab and parameter)?

Thank You.

Dears,

How to invoking key agreement method by gurux.

Best Regards,
Ahmed Hassan

Hi Mr. Kurumi. Please could you give me a hand with this prblem:
20:27:01 Initializing serial connection.
20:27:02 IEC Sending:/?!<CR><LF>
20:27:03 HDLC received: /SLB5\2SLB_AMBER_000001<CR><LF>
20:27:03 BaudRate is : 9600
20:27:03 Moving to mode E.
06 32 35 32 0D 0A
20:27:06 Send SNRM request.
7E A0 08 02 23 03 93 3E 74 7E
20:27:07
7E A0 21 03 00 02 00 23 73 7B 7F 81 80 12 05 01 80 06 01 80 07 04 00 00 00 01 08 04 00 00 00 01 53 3B 7E
20:27:07 Parsing UA reply succeeded.

When processing association view object list responses, it seems that DLMS Translator can understand and display the object list when it is returned in a get-response-normal response, but can't do the same in case when the object list is returned in get-response-with-datablock response.

First, an example where it correctly parses everything. I took the essential parts from this thread: https://www.gurux.fi/node/21382

Hi,

I am reading billing profile from meter and i see that scaler values in this case 1000 is applied only to cumulative energies but Tariff-wise energies are shown without scaler.

This report is causing interpretation issue. Attached is the reference pic for both bill profile and its scaler profile.

Request you to fix this issue.

Hi,
I can't connect to meter caused by "Unacceptable frame." error. Can you help me?

Hello,
please help. I fail to connect to Management Client. The message is "Index of array is out of bounds." It used to work in previous versions.
I am able to connect to Public Client.
Behaviour is the same for IP and HDLC connection.

Log:
Connect to Management Client via HDLC
9.0.2311.0602:
----------------------

7E A0 7 3 21 93 F 1 7E

7E A0 1E 21 3 73 C3 7A 81 80 12 5 1 80 6 1 80 7 4 0 0 0 1 8 4 0 0 0 1 53 3B 7E

7E A0 7 3 21 53 3 C7 7E

I am a commissioning engineer. My daily routine is to commission Modems connected to multiple DLMS meters. I usually have to add the devices one by one with their respective properties. It is a time taking and pretty tiring process to do on a daily basis. I was wondering if there’s a simpler way to add multiple meters in very few steps.

Thanks

Hi, I need to read Load profile data from Sanxing meter (P34S02 CT) with GXDLMSDirector. I can connect to the meter with password, Low Authentication, Client Address 1 (instead of 17 that is suggested for Sanxing), Logical Address 0, Physical Address 1), and I can read registers, clock,... but I can’t read Load Profile (Buffer). Access rights for attribute index 2 (Buffer) is Read, but Access Selector is only Entry. I can read only 1 (count) with ReadRowsByEntry, the rest are null values. Why don’t read more than 1 entry?