Hi,

I am using c code from our DLMS source.
here, while reading profile generic(OBIS code: 1,0,99,1,0,255), and adding more than 6 object shows "unacceptable frame error" in gurux dierector. but less than 6 is working fine.
please give me specific details about frame generation, if it had.

traced serial data from meter is pasted below.please find it.

thank you

received data from meter

7E A0 1E 21 03 73 C3 7A 81 80 12 05 01 80 06 01 80 07 04 00 00 00 01 08 04 00 00 00 01 53 3B 7E

12:41:34.026

Hi everyone.

I am having some problems with a Landis and Gyr Prepayment/Prepaid meter (Sample Unit) E460, regarding DisconnectControl.

I can read the values from the meter, but for some reason, I cannot write a command back to it,
the image indicates the presence of the DisconnectControls.

My question is, is this a access control issue that I do not have write access to the DisconnectControl object to "reconnect/disconnect"?

BR

Hi,
I'm trying to communicate with a meter ( Elster themis-uno EI6) in DLMSDirector.
With authentication "none" I have some response, but i can't reach obis for current index and many other needed.
Using authentication "none" and at the tab secure connection using "encryption" , system tile ( client system tile for management 8 bytes) , block cipher and authentication key same hex code for this specific meter , I get an error "Connection is permanently rejected . Authentication failure"

I have lots of parameters that i want to set in meter with serial port in C#.
I have
Class Name.
Data.
Class ID.
Attribute ID.
OBIS.
Data Type.
how can i do this???

After changing wifi connection during reading meter for the first time Director freezed.
Peter.

When I changed or added capture object I cannot read this Profile on Iskraemeco MT880.
Do you have some sugestion?
Peter.

Hi
Why error when clicking the "IECLocalPortSetup" object in the new "DLMSDirector" update?

Hello,
I’m getting hourly load profile (1.1.99.1.0.255) successfully from Kamstrup 382M meter.
But when I’m trying to read the same data from Kamstrup 351C meter, I’m getting back secondary values (1.1.1.8.0.129 not 1.1.1.8.0.255) of A14 (imported active energy ). The same with reactive energy.
Does anybody have any idea what I’m doing wrong or how to change that? I’m reading it remotely from UDP 4059 with client 0x12 from physical server 0x10 and logical server 0, using low authentication with default password.

Hello,

I found an incorrect page calculation in image transfer class.

The steps to reproduce the error are the following:

1. Connect to the meter and read the association (f5 key).

2. Open the window update pop up (selection of update file) and wait until the meter closes session due to the lack of keep alive messages. In my case, 1 minute.

3. Then, select one file and click OK.

4. Start the firmware update process and it will fail due to Disconnected state of the meter.

5. Connect again to the meter.

I Mister Miko

I'am try to connect a Janz B280 ussing a optical probe & i have read all data except Group D, data.
I try to change the Xml in the manufacturer option but en press apply, some errors appear.
I testwith defaul Gurux XML and the errors are the same.
Funny.
I Have some of XML from Janz/Contar and i like to test them. Send latter to your email
Can you help me to gain access to Group D Obis codes?
I find VT ratio for this device is VT=210 but since new and blank devices are VT=300. Funny.