hi, when I want to generate a P-384 certificate with Certificate generator, I get this error.how to solve this problem?
Thanks.

Hi Mr. Kurumi, I have problem with XML tab of the DXLMSdirector . The password is converted correctly but the cipher key and Authentication pass is not. The software translate differently the key that I write ( I choose HEX as I did in password). I send you the exact case to understand what I mean.

Hello,

I am in the process of testing a DLMS device that is in development in company. I have decided to try going through the conformance tests, and have ran into an issue when trying to pass the first one.

I downloaded the source code of Gurux DLMS Director to debug the application and try to find out why, but so far to no avail. The application does not accept the RR frame sent by the device.

The program reaches

client.GetData(GXByteBuffer reply, GXReplyData data, GXReplyData notify)

Hi,

please where can I set IEC device_address for start protocol IEC/ModeE in the GXDLMSDirector? That option was there a few years ago. But now I can't find it.

/? device_address ! <CR> <LF> <--- this device address

Thank you for help

Lubo

After reading the current association, when I try to read the instant push setup object in the push setup, GURUX throws an error index. why?

Hi Mr. Kurumi, after too many attempts and many combinations of settings finally I have connected with the Hexing 310 meter with High security, but no ciphering key and authentication encryption used. I have all the codes of the meter from the manufacturer (system title cipher key etc..) to connect with HLS_MD5 level but I need your help with the settings in security tad of the DLMSdirector software.
I have tried to connect 5 times with those settings

Hello,

I am using controller and follow below code to read IP data,

i16ret = cosem_init(&gMRICDataObj.base, DLMS_OBJECT_TYPE_DATA,
MR_INVOCATION_COUNTER_OBISCODE);

i16ret = cosem_init(&gInstantaneousProfileGenericObj.base,
DLMS_OBJECT_TYPE_PROFILE_GENERIC,
INSTANTANEOUS_PROFILE_OBISCODE);
cl_init(&cCon.settings, LOGICALNAMEREFERENCING, CLIENTADDRESS_PC,
SERVERADDRESS, DLMS_AUTHENTICATION_NONE, NULL,
DLMS_INTERFACE_TYPE_WRAPPER);
com_initializeConnection(&cCon);

Hello sir please I'm facing this issue and unable to solve this would you please help me
1: 7E A0 1B 21 00 02 04 01 30 2D CE E6 E7 00 4E 45 58 45 52 52 4F 52 4E 4F 2D 31 B8 00 7E
<HDLC len="1A" >
<TargetAddress Value="10" />
<!-- Logical address:1, Physical address:256 -->
<SourceAddress Value="4100" />
<!-- AARE frame. -->
<FrameType Value="30" />
<PDU>
<!-- Invalid length: 69. It should be: 10 -->

Hi,

I am trying to connect MeterSit G6 GPRS gas meter through GXDLMSDirector. But I don't have exact communication parameters. Does anyone have in their record?

Good day.

If i read the profile data with Map110 the Registers will show

1-1:1:5.0 (kW)
1-1:5:5.0 (kvar)
1-1:9:5.0 (kVA)

However when I read the same profile data with GXDLM I will get

1.1:1:4.0 (kW)
1.1:5:4.0 (kvar)
1.1:9:4.0 (kVA)

The data is the same for both, but the OBIS code is different.
The meter is set up with addresses as I see them in the Map110 Software.

I'm just trying to understand why it changes the register in the GXDLM software?