When I changed or added capture object I cannot read this Profile on Iskraemeco MT880.
Do you have some sugestion?
Peter.

Hi
Why error when clicking the "IECLocalPortSetup" object in the new "DLMSDirector" update?

Hello,
I’m getting hourly load profile (1.1.99.1.0.255) successfully from Kamstrup 382M meter.
But when I’m trying to read the same data from Kamstrup 351C meter, I’m getting back secondary values (1.1.1.8.0.129 not 1.1.1.8.0.255) of A14 (imported active energy ). The same with reactive energy.
Does anybody have any idea what I’m doing wrong or how to change that? I’m reading it remotely from UDP 4059 with client 0x12 from physical server 0x10 and logical server 0, using low authentication with default password.

Hello,

I found an incorrect page calculation in image transfer class.

The steps to reproduce the error are the following:

1. Connect to the meter and read the association (f5 key).

2. Open the window update pop up (selection of update file) and wait until the meter closes session due to the lack of keep alive messages. In my case, 1 minute.

3. Then, select one file and click OK.

4. Start the firmware update process and it will fail due to Disconnected state of the meter.

5. Connect again to the meter.

I Mister Miko

I'am try to connect a Janz B280 ussing a optical probe & i have read all data except Group D, data.
I try to change the Xml in the manufacturer option but en press apply, some errors appear.
I testwith defaul Gurux XML and the errors are the same.
Funny.
I Have some of XML from Janz/Contar and i like to test them. Send latter to your email
Can you help me to gain access to Group D Obis codes?
I find VT ratio for this device is VT=210 but since new and blank devices are VT=300. Funny.

Hi Mikko,

I am working with Gurux GXDLMSDirector configured as:

Authentication: HighGMAC
Interface: HDLC
Media: Serial
Security: AuthenticationEncryption

When I use the 8.2.1912.0501 version gurux works fine with my meter, but when I try to establish a connection with 8.1.2002.0101 version, gurux sends the message:

ACCESS Error: Devise reports a hardware fault.

Hi,
I am used ER300p energy meter(L&T). It is a Indian Standard meter. I am used optical cable to read the dlms data using GXDLMSDirector.
I have get some data from the GXDLMSDirector. After some time, its given a error was fail to receive reply from the device in given time. I was not found data of KWh, KVArh and other. I have attached the screen shot below.
Same question ask the other person, you said Try to change the authentication level from None to low or High.How to find authentication password, I do not have any manual ?

Hi,

I'm trying to connect to ACE SL7000 through dlms director based on default settings from http://www.gurux.fi//GXDLMSDirectorExample.

After sending SNRM request meter is not responding:

Hello!

I have a ISKRA AM550 from "Kärntennetz" in Austria. They provide a read only interface which pushes a message every second. I recorded an example with a serial monitor:

7E A0 77 CF 02 23 13 BB 45 E6 E7 00 DB 08 49 53 4B 69 74 55 0B CD 5F 20 00 00 0C B0 3C BB 27 4E 90 5F 09 74 9D 5C 31 36 CC B7 47 57 C5 FC 3A 35 7B AB 06 17 46 94 BB 5C 93 73 82 5F D7 76 77 E5 D9 21 92 17 B2 71 25 E8 CA B2 C0 1B 84 2E 75 6A C8 D0 71 85 FB 2D DF 66 31 89 EF 3E 8C 03 DE 2B B9 C1 68 B8 BF A7 D3 A4 CE F3 19 3F 83 21 E0 06 44 B4 A0 82 3C 92 A0 C0 7E

Hello.

I'm trying to read Landis+Gyr Meter (ZMD405CT44.2407) as i did times before with older versions of gurux DLMS. Now I encounter error when i'm getting the association view.

I get the following error: Unacceptable Frame 3 times in a row and then it shows connected but no object list gets created as it was in previous versions.

If I hit refresh button the error is more specficic as: "GetObjects Failed: Unacceptable Frame"

I got the same behaviour with 3 different meters from the same brand and the exact same model.