I am using HPL EB METER.I am trying to format the data which are coming out from the EB meter serially.I can able to receive data from the serial terminal. I am using below-mentioned cmd to get the response.

Reuest:
7E A0 0A 00 02 04 01 41 93 22 D0 7E

Response
7E A0 21 41 00 02 04 01 73 1E 06 81 80 12 05 01 80 06 01 80 07 04 00 00 00 01 08 04 00 00 00 01 53 3B 7E

Here I would like to know which is indicating R, Y, B voltages, current, other parameters.
I am also searching some user manual on the internet.

Hi there,
I am new to Dlms director. I have tried to connect with several meters and succesfully able to communicate.

But i always cant see adjust or shift_time actions on clock object in Gurux DLMS director. Is there anywhere i can add specific attributes to the clock object to support actions.

Regards,
Bhavana Kotagiri.

Hi Mikko,
Previously I asked u about LIN YANG meter and you helpful guided me that it send data with ciphering method.
I ask some information of manufacturer and understand that the frame type is 1 (0X80) and they have defined special command. They said ciphering setting is like DLMS and ciphering key is default value.
Frame format:
7E TYPE(1Byte) Frame len(1 byte) Cmd(1byte) data FCS(2byte) 7E

Hi,
I am using GENUS meter (DLMS compliant) to get data from the tool but no matter what values I set the meter is not responding
I know the issue is probably with the values I set, so please help me debug
This is the value I am sending

Baud Rate - 9600
Data Bits - 8
Parity - EVEN
Stop Bits - ONE
Physical Server - 2 Logical Server - 1
Start Protocol - DLMS
Auth - LOW PW - 1A2B3C4D

(Check the screen shot too)

hi

I made one demo project with 10 Energy meter.
All 10 meter are connected with Mess Network.
There is one RF+GSM gateway which is connected with Mess network too.
Meter has its own protocol ,not DLMS,and all work fine,i got date on server side.

now I have one sample Energy Meter ,which have indian Standard.
I have optical port, which is connected with computer via serial port.
I install Gurux GXDLMSDirector Ver 8.1

I attached device properties screenshot

Hi
I try to read LY-SM100. I used Certification No. 1858 information of dlms site
http://www.dlms.com/conformance/listofcompliantequipment/index.html
and create a new manufacture and then add device like this:

Hi,

I was using EMH ITZ and Moxa NPORT 5232 but it can't connect. Here my device
manufacturer emh
startprotocol: dlms
media :net
auth none
client address 10
adress type serialnumber
serial number i put 8075
logical server 0
host name 192.168.127.254
port 4059

Hi,

Hi, I am not expert in DLMS protocol. I have communicated with HXF300 electrical meter using GXDLMSDirector. everything is OK except getting objects.
I have sent fallowing frame (using GXDLMSDirector):
7E A0 19 03 21 32 6F D8 E6 E6 00 C0 01 C1 00 01 01 00 81 81 00 FF 02 00 5B 2D 7E

it responds with:
7E A0 11 21 03 52 B1 F8 E6 E7 00 C4 01 01 01 04 56 FC 7E

I dont know what the bytes of "01 01 04" stand for. I cant understand the tag and it's value.

Hai

I have used DLMS director to connect with my smart meter. I'm getting certain objects with abnormal OBIS codes. My understanding is, OBIS codes normally end with 255. But i'm getting some objects that has OBIS codes which end with 101.102,103 etc.'
Please have a look into the picture that i have attached. Please help me in knowing whether it is a normal scenario or an abnormal one.

Thanks & Regards
Anbarasan